Gallery of new files
Jump to navigation
Jump to search
This special page shows the last uploaded files.
- Ameca shoulder loom - pull out through shoulder - leave earth wire in place.jpg Marcus
09:30, 12 December 2022
4,000 × 2,992; 736 KB
- Ameca shoulder loom - path continues under neck motor driver board.jpg Marcus
09:30, 12 December 2022
4,000 × 2,992; 1.87 MB
- Ameca shoulder loom and earth wire - path through shoulder - cable ties removed.jpg Marcus
09:30, 12 December 2022
4,000 × 2,992; 902 KB
- Ameca shoulder loom and earth wire - path through shoulder.jpg Marcus
09:30, 12 December 2022
2,992 × 4,000; 903 KB
- Ameca shoulder loom and earth wire - cut cable ties to separate from earth wire.jpg Marcus
09:30, 12 December 2022
2,992 × 4,000; 1.19 MB
- Ameca upper arm - note the single black earth wire with red plug - do not cut this.jpg Marcus
09:30, 12 December 2022
2,992 × 4,000; 708 KB
- Ameca upper arm - cut shoulder loom near shoulder. DO NO CUT the black earth wire or any other wires.jpg Marcus
09:30, 12 December 2022
2,992 × 4,000; 868 KB
- Ameca upper arm - unscrew p-clip retaining shoulder loom and black earth wire.jpg Marcus
09:30, 12 December 2022
3,000 × 4,000; 479 KB
- Ameca upper arm - unplug shoulder loom - squeeze clip at top of micro lock plug to release.jpg Marcus
09:30, 12 December 2022
2,992 × 4,000; 1.36 MB
- Ameca upper arm outer trim - unscrew 3 off Torx 20 screws to remove.jpg Marcus
09:30, 12 December 2022
2,992 × 4,000; 1.7 MB
- Ameca rear torso shell removed - note the cooling fan plug.jpg Marcus
09:30, 12 December 2022
2,992 × 4,000; 227 KB
- Ameca rear torso shell - NOTE cooling fan wiring.jpg Marcus
09:30, 12 December 2022
2,992 × 4,000; 1.51 MB
- Ameca rear torso shell - unplug cooling fan wiring to remove shell.jpg Marcus
09:30, 12 December 2022
2,992 × 4,000; 762 KB
- Ameca rear torso shell - silicon un-poppered.jpg Marcus
09:30, 12 December 2022
2,992 × 4,000; 1.12 MB
- Ameca rear torso shell - remove 4 off Torx 20 screws.jpg Marcus
09:30, 12 December 2022
2,992 × 4,000; 803 KB
- Ameca silicon removal - hold silicon as near as possible to popper - grip popper with nail.jpg Marcus
08:10, 12 December 2022
2,992 × 4,000; 384 KB
- Jun Air OF302-25M set robot pressure to 6 bar.jpg Marcus
16:34, 9 February 2022
4,000 × 2,992; 1.17 MB
- Jun Air OF302-25M Instructions inside compressor.jpg Marcus
16:33, 9 February 2022
2,992 × 4,000; 444 KB
- Jun Air OF302-25M Instructions, condensate container (bubble wrapped) and air line inside compressor.jpg Marcus
16:32, 9 February 2022
4,000 × 2,992; 933 KB
- Jun Air OF302-25M rear - hex standoffs fitted.jpg Marcus
16:24, 9 February 2022
4,000 × 2,992; 773 KB
- NUC breakout with audio default switch positions and labels.jpg Marcus
11:38, 27 January 2022
1,600 × 1,200; 533 KB
- KS-0023 serial plate location - legs - visible during shipping - close view rotated.png Marcus
13:03, 5 October 2021
569 × 422; 249 KB
- KS-0023 serial plate location - legs - visible during shipping - close view.png Marcus
13:02, 5 October 2021
425 × 559; 201 KB
- KS-0023 serial plate location - legs - visible during shipping.png Marcus
13:01, 5 October 2021
418 × 557; 315 KB