Gallery of new files
Jump to navigation
Jump to search
This special page shows the last uploaded files.
- XLR out connector - disconnecting 2 - hold tab and disconnect.jpg Marcus
14:30, 28 January 2021
4,000 × 2,992; 1.4 MB
- XLR out connector - disconnecting 1 - press down tab.jpg Marcus
14:29, 28 January 2021
4,000 × 2,992; 352 KB
- XLR out connector - connecting - align and push in till locks in place.jpg Marcus
14:28, 28 January 2021
4,000 × 2,992; 1.16 MB
- PowerCON connector 3 - twist straight and release to lock.jpg Marcus
14:00, 28 January 2021
1,600 × 1,197; 456 KB
- Torso roll motor and encoder connection at waist.jpg Marcus
10:13, 1 July 2020
1,920 × 1,080; 580 KB
- Removing finger valve plugs - press on clip at rear.jpg Marcus
12:15, 8 April 2020
4,032 × 2,268; 320 KB
- Mesmer - fit jacket - bags on hands help slide on sleeves.jpg Marcus
16:32, 24 March 2020
3,024 × 4,032; 430 KB
- Mesmer - left arm mount with black spacer in place.jpg Marcus
15:38, 24 March 2020
4,032 × 2,268; 460 KB
- Mesmer - left arm unpacking - can leave protective tissue on.jpg Marcus
15:36, 24 March 2020
1,600 × 1,200; 357 KB
- Mesmer - left arm unpacking - protective foam layer.jpg Marcus
15:35, 24 March 2020
1,600 × 1,200; 169 KB
- Mesmer - gas strut mounting upper pivot - rear view.jpg Marcus
15:16, 24 March 2020
1,280 × 720; 97 KB
- Mesmer - right arm, mount with bracket vertical (nut facing to rear).jpg Marcus
13:05, 23 March 2020
1,600 × 1,200; 345 KB
- Mesmer - right arm unpacking - can leave protective tissue on for now.jpg Marcus
15:49, 20 March 2020
1,600 × 1,200; 348 KB
- Mesmer - right arm unpacking - protective foam layer.jpg Marcus
15:48, 20 March 2020
1,600 × 1,200; 233 KB
- Mesmer - connect Vrpi inside torso and feed Ethernet cable out of hole.jpg Marcus
15:13, 20 March 2020
1,280 × 720; 85 KB
- Mesmer - controller (Raspberry Pi) with shield removed.jpg Marcus
14:07, 20 March 2020
4,032 × 2,268; 376 KB
- Mesmer - undo 2 screws and remove controller shield.jpg Marcus
14:06, 20 March 2020
4,032 × 2,268; 766 KB
- Mesmer - torso - secure speaker cable with p-clip.jpg Marcus
14:00, 20 March 2020
4,030 × 2,267; 485 KB
- Mesmer - torso - power and braided comms cables into torso.jpg Marcus
13:52, 20 March 2020
4,032 × 2,268; 301 KB
- Mesmer - ease the torso down as far as possible onto legs.jpg Marcus
11:55, 20 March 2020
2,268 × 4,032; 447 KB
- Mesmer - leg shells removed and set to one side.jpg Marcus
11:49, 20 March 2020
4,032 × 2,268; 828 KB
- Mesmer - rear pelvis shell - white tape over screw locations.jpg Marcus
10:15, 20 March 2020
1,600 × 1,200; 442 KB
- Mesmer - rear pelvis shell wrapped for shipping.jpg Marcus
10:14, 20 March 2020
1,600 × 1,200; 316 KB
- Mesmer - torso handling - rest chin on shoulder.jpg Marcus
16:32, 19 March 2020
4,032 × 2,268; 398 KB
- Mesmer - tighten bolts at ankles to retain legs.jpg Marcus
16:26, 18 March 2020
4,032 × 2,268; 742 KB
- Mesmer - fit trousers before attaching legs to base.jpg Marcus
16:25, 18 March 2020
2,268 × 4,032; 1.62 MB
- V0 3 board mounting - screw on case with M2 5 x 6 TX8 screws.jpg Marcus
16:54, 25 February 2020
4,032 × 3,024; 379 KB
- V0 3 board mounting - M2 5 x 20mm standoffs through board.jpg Marcus
16:48, 25 February 2020
4,032 × 3,024; 559 KB
- V0 3 board mounting - thermal conductive tape under usb hub.jpg Marcus
16:46, 25 February 2020
4,032 × 3,024; 438 KB
- V0 3 board with polarity reversing adaptor bottom view.jpg Marcus
16:32, 25 February 2020
4,032 × 3,024; 737 KB
- V0 3 board with polarity reversing adaptor side view.jpg Marcus
16:31, 25 February 2020
4,032 × 3,024; 689 KB
- RoboThespian Assembly and Safety Instructions.pdf Marcus
12:36, 12 February 2020
1,240 × 874, 6 pages; 5.08 MB
- Remove bolts from either side of the finger.jpg Chris.c
08:04, 7 October 2019
4,032 × 3,024; 3.22 MB
- Remove M2 bolts from side and wrist of hand.jpg Chris.c
07:37, 7 October 2019
4,032 × 3,024; 4.79 MB
- RoboThespian power board - NUC - 24v supply plug released.jpg Marcus
11:44, 21 May 2019
1,600 × 1,200; 164 KB
- RoboThespian power board - NUC - press metal to release 24v supply plug.jpg Marcus
11:44, 21 May 2019
4,032 × 3,024; 1.28 MB
- RoboThespian Head board with TX25s LCDs cheek LEDs.jpg Marcus
13:36, 20 May 2019
1,280 × 720; 153 KB
- SociBot Kiosk with blanking plate - ethernet network connection.jpg Marcus
10:49, 16 April 2019
1,080 × 1,440; 176 KB
- SociBot Kiosk with blanking plate - base plate.png Marcus
10:41, 16 April 2019
1,080 × 1,440; 139 KB
- SociBot Kiosk with blanking plate - power connection.jpg Marcus
09:46, 16 April 2019
1,080 × 1,440; 186 KB